bitcoin/doc/cjdns.md

CJDNS support in Bitcoin Core

It is possible to run Bitcoin Core over CJDNS, an encrypted IPv6 network that uses public-key cryptography for address allocation and a distributed hash table for routing.

What is CJDNS?

CJDNS is like a distributed, shared VPN with multiple entry points where every participant can reach any other participant. All participants use addresses from the fc00::/8 network (reserved IPv6 range). Installation and configuration is done outside of Bitcoin Core, similarly to a VPN (either in the host/OS or on the network router). See https://github.com/cjdelisle/cjdns#readme for more information.

Compared to IPv4/IPv6, CJDNS provides end-to-end encryption and protects nodes from traffic analysis and filtering.

Used with Tor and I2P, CJDNS is a complementary option that can enhance network redundancy and robustness for both the Bitcoin network and individual nodes.

Each network has different characteristics. For instance, Tor is widely used but somewhat centralized. I2P connections have a source address and I2P is slow. CJDNS is fast but does not hide the sender and the recipient from intermediate routers.

Installing CJDNS

To install and set up CJDNS, follow the instructions at https://github.com/cjdelisle/cjdns#how-to-install-cjdns.

Connecting to the CJDNS network

As of CJDNS v22, nodes automatically discover and connect to peers via DNS seeding. After installation, you can verify that your node has peers:

cjdnstool peers show

If you see peers with status ESTABLISHED, your node is connected and no further peering setup is needed.

Manual peering may be useful if you want to guarantee a connection to a specific node, or if you have disabled DNS seeding for privacy reasons. See doc/peering.md in the CJDNS repository for details.

Run Bitcoin Core with CJDNS

Once you are connected to the CJDNS network, the following Bitcoin Core configuration option makes CJDNS peers automatically reachable:

-cjdnsreachable

When enabled, this option tells Bitcoin Core that it is running in an environment where a connection to an fc00::/8 address will be to the CJDNS network instead of to an RFC4193 IPv6 local network. This helps Bitcoin Core perform better address management:

• Your node can consider incoming fc00::/8 connections to be from the CJDNS network rather than from an IPv6 private one.
• If one of your node's local addresses is fc00::/8, then it can choose to gossip that address to peers.

Additional configuration options related to CJDNS

-onlynet=cjdns

Make automatic outbound connections only to CJDNS addresses. Inbound and manual connections are not affected by this option. It can be specified multiple times to allow multiple networks, e.g. onlynet=cjdns, onlynet=i2p, onlynet=onion.

CJDNS support was added to Bitcoin Core in version 23.0 and there may be fewer CJDNS peers than Tor or IP ones. You can use bitcoin-cli -addrinfo to see the number of CJDNS addresses known to your node.

In general, a node can be run with both an onion service and CJDNS (or any/all of IPv4/IPv6/onion/I2P/CJDNS), which can provide a potential fallback if one of the networks has issues. There are a number of ways to configure this; see doc/tor.md for details.

CJDNS-related information in Bitcoin Core

There are several ways to see your CJDNS address in Bitcoin Core:

• in the "Local addresses" output of CLI -netinfo
• in the "localaddresses" output of RPC getnetworkinfo

To see which CJDNS peers your node is connected to, use bitcoin-cli -netinfo 4 or the getpeerinfo RPC (i.e. bitcoin-cli getpeerinfo).

You can use the getnodeaddresses RPC to fetch a number of CJDNS peers known to your node; run bitcoin-cli help getnodeaddresses for details.

bitcoin rpc can also be substituted for bitcoin-cli.